Netinstall for windows 10 download

If you followed the guide precisely, then you should not have any Internet connection on your computer, Windows 10 wants to verify all apps that it runs, but will not be able to do it since lack of the Internet connection, for this reason, a warning might pop up, you should click Run. Netinstall requires administrator rights, there should be a window asking for permissions to run Netinstall, you must accept these permissions in order for Netinstall to work properly.

Some computers have a network interface especially USB Ethernet adapters that tend to create an extra link flap, which is enough for Netinstall to fail to detect a device that is in Etherboot mode. In such a case you can use a switch between your device and your computer or a router in bridge mode to prevent this issue. There are multiple ways how to put your device into Etherboot mode. Make sure you read the Etherboot manual before trying to put the device into this mode.

Methods vary between different MikroTik devices. If you downloaded RouterOS packages for multiple architectures, then Netinstall will only show the appropriate architecture packages for your device after you have selected it.

All unsupported packages will not show up in this window after you have selected a device. If the installation does not start progress bar is not moving or no status is shown , then you can try closing the Netinstall application and opening it up again or try to put the device into Etherboot mode again.

If you are still unable to get Netinstall working, then you should try using it on a different computer since there might be an operating system's issue that is preventing Netinstall from working properly.

After using Netinstall the device will be reset to defaults unless you specified not to apply default configuration. Some devices are not accessible through ether1 port with the default configuration for security reasons. Read more about Default configuration. When using the Configure script option, it is suggested to introduce a delay before configuration execution. The Linux version is a command line tool, which offers nearly the same parameters as the Windows counterpart.

Etherboot mode is a special state for a MikroTik device that allows you to reinstall your device using Netinstall. There are several ways to put your device into Etherboot mode depending on the device you are using. The Reset can be found on all MikroTik devices, this button can be used to put the device into Etherboot mode.

An easy way to put a device into Etherboot mode using the Reset button is by powering off the device, hold the Reset button, power on the device while holding the Reset button and keep holding it until the device shows up in your Netinstalll window. If you have set up a Protected bootloader , then the reset button's behavior is changed. Make sure you remember the settings you used to set up the Protected bootloader, otherwise you will not be able to use Eterboot mode and will not be able to reset your device.

If your device is able to boot up and you are able to log in, then you can easily put the device into Etherboot mode. To do so, just connect to your device and execute the following command:.

After that either reboot the device or do a power cycle on the device. Next time the device will boot up, then it will first try going into Etherboot mode. Note that after the first boot up, the device will not try going into Etherboot mode and will boot directly of NAND or of the storage type the device is using. Some devices come with a serial console that can be used to put the device into Etherboot mode. To do so, make sure you configure your computer's serial console. Make sure you are using a proper null modem cable, you can find the proper pinout here.

At this point your device is in Etherboot mode, now the device should show up in your Netinstall window. NET Framework versions that you need. NET Framework 4.

You may have arrived on this page after trying to run an application and seeing a dialog on your machine similar to the following one:. You can install. If you're using Windows 10 or and you want to install the.

NET Framework version on Windows 10 and Follow the instructions to install. NET Framework 3. You cannot install an earlier version of the. NET Framework on your machine if a later version is already installed. NET Framework can be used to run applications built for the. For example,. The latest version the.

NET Framework starting with 4. For a list of all the versions of the. NET Framework available to download, see the. NET Downloads page.